tail numbers

tail numbers

I remember reading about the size requirements in one of the issues but no longer have the article. I can't seem to find the information in ac 43-13. The numbers on my plane are about 6-7", it's a 1961 model

Guest
Guest
useravatar
Offline
Posts
User info in posts
Only registered users or members can reply or post

Re: tail numbers

  Section 45.29: Size of marks.


(a) Except as provided in paragraph (f) of this section, each operator of an aircraft shall display marks on the aircraft meeting the size requirements of this section.
(b) Height. Except as provided in paragraph (h) of this part, the nationality and registration marks must be of equal height and on--
(1) Fixed-wing aircraft, must be at least 12 inches high, except that:
(i) An aircraft displaying marks at least 2 inches high before November 1, 1981 and an aircraft manufactured after November 2, 1981, but before January 1, 1983, may display those marks until the aircraft is repainted or the marks are repainted, restored, or changed;
(ii) Marks at least 3 inches high may be displayed on a glider;
(iii) Marks at least 3 inches high may be displayed on an aircraft for which an experimental certificate has been issued under Sec. 21.191(d) or 21.191(g) for operating as an exhibition aircraft or as an amateur-built aircraft when the maximum cruising speed of the aircraft does not exceed 180 knots CAS; and
(iv) Marks may be displayed on an exhibition, antique, or other aircraft in accordance with Sec. 45.22.
(2) Airships, spherical balloons, and nonspherical balloons, must be at least 3 inches high; and
(3) Rotorcraft, must be at least 12 inches high, except that rotorcraft displaying before April 18, 1983, marks required by Sec. 45.29(b)(3) in effect on April 17, 1983, and rotorcraft manufactured on or after April 18, 1983, but before December 31, 1983, may display those marks until the aircraft is repainted or the marks are repainted, restored, or changed.
(c) Width. Characters must be two-thirds as wide as they are high, except the number ``1'', which must be one-sixth as wide as it is high, and the letters ``M'' and ``W'' which may be as wide as they are high.
(d) Thickness. Characters must be formed by solid lines one-sixth as thick as the character is high.
(e) Spacing. The space between each character may not be less than one-fourth of the character width.
(f) If either one of the surfaces authorized for displaying required marks under Sec. 45.25 is large enough for display of marks meeting the size requirements of this section and the other is not, full-size marks shall be placed on the larger surface. If neither surface is large enough for full-size marks, marks as large as practicable shall be displayed on the larger of the two surfaces. If any surface authorized to be marked by Sec. 45.27 is not large enough for full-size marks, marks as large as practicable shall be placed on the largest of the authorized surfaces.
(g) Uniformity. The marks required by this part for fixed-wing aircraft must have the same height, width, thickness, and spacing on both sides of the aircraft.
(h) After March 7, 1988, each operator of an aircraft penetrating an ADIZ or DEWIZ shall display on that aircraft temporary or permanent nationality and registration marks at least 12 inches high.

Guest
Guest
useravatar
Offline
Posts
User info in posts
Only registered users or members can reply or post

Board Info

Board Stats:
 
Total Topics:
6043
Total Polls:
1
Total Posts:
16350
Dormant:
User Info:
 
Total Users:
2528
Newest User:
jmlinke@aol.com
Members Online:
0
Guests Online:
3218

Online: 
There are no members online

Forum Legend:

 Topic
 New
 Locked
 Sticky
 Active
 New/Active
 New/Locked
 New Sticky
 Locked/Active
 Active/Sticky
 Sticky/Locked
 Sticky/Active/Locked

ankara escort ankara rus escort ankara escort bayan ankara bayan partner ankara escort kizlar escort ankara ankara escort ankara eskort ankara escort bayan ankara bayan partner ankara escort kizlar escort ankara